Craigs Labs LLC

The product line

A small, calibrated sensor package with its own data acquisition module, built for one industry-specific job in testing or manufacturing. Plug it into a phone or tablet, carry it into the field, and start recording.

Eight probes on an acquisition hub, with a tablet showing live charts
An eight-channel temperature and humidity package: hub, probes and tablet, ready to log.

How it fits together

Every sensor in the CL-Link line speaks I2C over standard 4-pin M12 circular connectors. Each module has a male and a female end, so you daisy-chain as many sensors as the job needs, in parallel, on just two data lines. Up to 127 devices can share one bus. A small in-line microcontroller module sits on the chain, and a phone or tablet powers it over USB and records the data.

Phone / tablet USB In-line MCU Load cell24-bit ADC WeatherT / RH / baro Pressure±100 mbar USB powers the chain · M12 4-pin, IP67 · two data lines · up to 127 devices

Some arrangements may use larger acquisition modules with a separate port for each sensor, for sensors that don't use I2C, such as thermocouples. With simple USB hubs, multiple modules can also run in parallel while fully integrating with the same software that records and analyses the data.

CL-Link sensor modules

I2C sensor modules on IP67 M12 over-molded cables and panel-mount connectors. Calibrated before they ship.

Black aluminium in-line module with an M12 connector

CL-LC24

In-line load cell amplifier

An ultra-low-profile, aluminium-housed, in-line 24-bit ADC with a precision voltage reference and a programmable gain amplifier. It works with any full-bridge strain gauge load cell, S-type or parallel beam.

  • 24-bit resolution
  • Programmable gain
  • Precision voltage reference
Weather module with a small in-line MCU and USB plug

CL-WX

Weather module

Temperature, humidity and barometric pressure, with a high sample rate, high accuracy and fast response. Most humidity sensors are slow to respond, but this one picks up a change right away. Use it to apply climate correction factors to your measurements automatically.

  • Temp · RH · barometric
  • Fast humidity response
  • Automatic climate correction
Aluminium transducer housing with two brass pressure ports

CL-DP100

Differential pressure transducer

±100 mbar differential pressure for fenestration (window and door) testing, built around a high-accuracy, high-resolution Honeywell transducer. It's rated for millions of pressure cycles, including severe over-pressure, without needing recalibration.

  • ±100 mbar differential
  • Millions of cycles
  • No recalibration needed
Pressure gauge on a fitting with an M12 cable

CL-HP

Hydraulic and pneumatic pressure

Pressure transducer modules for load testing driven by hydraulics or pneumatics. Pair one with a CL-WX on the same two data lines to apply correction factors in pneumatic flow-rate work.

  • Hydraulic or pneumatic
  • Range chosen for your application
Eight temperature and humidity probes on one acquisition module, with a tablet

CL-TH8

Eight-channel temperature and humidity

Eight dual temperature and humidity probes on a single module. Use it to map a chamber, an oven, a curing room or a whole production line.

  • 8 channels
  • Dual temp + RH probes
Inline flow rate sensor with an M12 cable

Flow rate

Flow rate sensor

An inline flow sensor that plugs onto the same M12 chain as the other CL-Link sensors, so flow is logged alongside weather, pressure and load.

CL-TC

Thermocouple module

Thermocouple inputs with cold-junction compensation, for high-temperature work that standard probes can't handle.

  • Thermocouple inputs
  • Cold-junction compensated

CL-DX

Deflection and displacement

Measure deflection under load alongside force and pressure on the same bus, so every reading lines up in time.

  • Deflection · displacement
  • Time-aligned with load data

In development

Motion and vibration

We're developing a wider range of instruments, including sensors for motion, vibration and displacement. Need something that isn't listed? Ask us.

Data acquisition modules

The modules that sit between your sensors and your screen.

Small blue-cornered CL-Link module

CL-Link MCU

In-line microcontroller module

A small module that sits on the M12 chain and runs the whole I2C line. Power it from a phone or tablet over USB, so there's no separate supply to carry into the field.

  • Up to 127 devices per bus
  • USB powered
  • Windows and Android
Flow rate sensor and weather module both plugged into one in-line MCU, with a USB plug

Example chain

Flow and weather on one MCU

A flow rate sensor and a weather module, both plugged into a single in-line MCU, which runs on USB from the phone or tablet.

Extruded aluminium enclosure with blue silicone rubber corners

CL-Hub

Application-agnostic acquisition hub

A larger module with a separate connector for each sensor. It's housed in extruded aluminium with silicone rubber molded corners and has M12 interconnects. Everything is IP67 rated against submersion, impact and debris, including the USB port.

  • IP67 throughout, IP67 USB
  • Extruded aluminium, silicone corners
  • Open source electronics hardware

Final enclosure design pending.

Multi-channel hub with load cell, in-line ADC and MCU modules, and a pressure transducer on M12 cables

CL-Scale

Multi-channel load cell module

Made for platform scales with four or more load cells. It reads each cell on its own channel, so you get the total weight and can also see how the load is spread across the platform.

The photo shows one example arrangement: an in-line 24-bit load cell ADC (CL-LC24), an in-line MCU module that daisy-chains over M12 connectors with splitters, and a CL-DP100 differential pressure transducer. Many arrangements can be made from these same modules.

  • 4+ load cell channels
  • S-type or parallel beam

Software for Windows and Android

CL-Studio

Graphing, data logging and analysis

A full-featured application built for tablets. Record data, chart it and analyse it, from a quick test in the field to months of continuous logging.

  • Slide-out toolbars on all four edges of the screen, built for touch.
  • Graph tools, analysis tools and indicators, with a full New / Open / Save / Save As file menu.
  • Import and export: XLS, CSV, SQLite, JPG, BMP, PNG and PDF.
  • Zoom like a map. Database optimisations let you pan and zoom through months or even years of data, with more detail appearing as you zoom in. It stays fast and light on any amount of data.
  • Runs on Windows and Android, so you can record on a phone in the field and analyse on a tablet or PC.
CL-Studio on a desktop screen, with two charts of logged sensor data

Calibrated sensor packages

This is what we really sell. You tell us what needs measuring. We choose the sensors, calibrate them, build them into one package with the right acquisition module, and set up the software for your test. We'll work with your calibration lab to meet your requirements, train your staff on site, and make software changes quickly and affordably, with AI-assisted development. Some examples:

Window and door testing

A CL-DP100 differential pressure transducer plus a CL-WX weather module on the same two wires. Climate corrections are applied automatically during fenestration tests.

Load and materials testing

CL-LC24 load cells, CL-HP hydraulic or pneumatic pressure and CL-DX deflection on one chain, all time-aligned for force-versus-deflection curves.

Platform and process scales

A CL-Scale module with four or more load cells, for weighing, checkweighing and fill monitoring on the production line.

Environmental mapping

CL-TH8 and CL-TC modules for chambers, ovens, curing rooms and warehouses, logged for months and reviewed in minutes.

Field kits

Sensors, a CL-Link MCU and a phone. Plug in, carry it around the site, and bring the data back to the office.

Parts library and breakout boards

Behind every package is our library of tested designs. It includes bills of materials, breakout boards for 24-bit ADCs, and interface boards for a wide range of digital and analogue sensors. This is why we can turn a new sensor package around quickly.

24-bit ADC breakouts

Precision front ends for strain gauges, bridges and low-level analogue signals.

Sensor interface boards

Proven circuits for digital and analogue sensors, including pressure, force, temperature, humidity and barometric sensors.

M12 cables and connectors

IP67 over-molded cables, panel-mount connectors and internal interconnects, with production sourcing finalised.

BOMs and documentation

Every design comes with a full bill of materials, so packages can be built repeatably and supported for years.

Prototypes and internals

Inside the hub: M12 panel-mount connectors, twisted-pair internal wiring and open source microcontroller hardware. These are early-generation builds. Production enclosures are still being finalised.

Have a test in mind?

Tell us what you need to measure and where. We'll suggest a sensor package.

Get in touch